SST
Special tools for Hyundai/Kia Motors
AboutProducts
SST
This page is a list of special tools exclusively for Hyundai/Kia sold by our company
You can search the special tool you want by product name/product number through Ctrl+F4 (Find).
| Eco-friendly car | Part number | name | Applicable vehicle type | size(mm) | How to use | img |
|---|---|---|---|---|---|---|
|
09090-09000 | INSULATED TOOL SET(CASE) | EV,HEV, FCEV all vehicles | 486/364/124 |
|
|
|
09090-10000 | INSULATED TOOL SET(FORM) | EV,HEV, FCEV all vehicles |
|
||
| 09240-2J100 | OCV center bolt replacement tool | N/v 2.0 ENGIN | 70/35/40 | Secures the camshaft when removing the OCV center bolt. |
|
|
|
09253-J2300 | COOLANT REFILLER & DRAIN TOOL | EV,HEV, FCEV all vehicles | 574/307/154 | Used for coolant discharge and vacuum suction용 |
|
|
09253-J2310 | COOLANT REFILLER & SUCTION TOOL | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2320 | CAP ADAPTOR A | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2330 | CAP ADAPTOR B | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2340 | CAP ADAPTOR C | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2350 | CAP ADAPTOR D | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2360 | CAP ADAPTOR E | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2370 | HOSE SET | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2380 | COOLANT DRAIN ADAPTOR & HOSE | EV,HEV, FCEV all vehicles |
|
||
|
09253-J2390 | HOSE CLAMP | EV,HEV, FCEV all vehicles |
|
||
 |
09253-J2301 | FC-EV Coolant Airfiter | FCEV all vehicles |
|
||
|
09253-J2302 | FC-EV Sealed Adapter | FCEV all vehicles |
|
||
|
09253-J2303 | FC-EV Exhaust Adapter | FCEV all vehicles |
|
||
| 09353-29000 | fuel pressure gauge adapter | 55/40/40 |
|
|||
| 09353-AL100 | FUEL PRESSURE GAUGE | Euro6 (D,A,U,S,R ENG) | 150/135/120 | Used to measure fuel (diesel) pressure |
|
|
| 09353-AL200 | FUEL PRESSURE GAUGE ADAPTER | Euro6 (D,A,U,S,R ENG) | 300/240/30 | Used to measure fuel (diesel) pressure |
|
|
|
|
09356-4W100 | REMOVER-TUBE(Small) | Tucson(LM) FCEV | 35/35/15 | Used to remove the connector at the outlet of the hydrogen tank of a hydrogen fuel cell vehicle. |
|
| |
09356-4W110 | REMOVER-TUBE (Large) | Tucson(LM)/NEXO(FE) FCEV | 50/40/20 | Used to remove the connector at the outlet of the hydrogen tank of a hydrogen fuel cell vehicle. | |
| |
09356-4W120 | HOSE | Tucson(LM) FCEV | 320/200/50 | Used to remove residual pressure in hydrogen fuel cell vehicles. |
|
| |
09356-4W130 | FUEL PRESSURE GAUGE & HOSE | Tucson(LM)/NEXO(FE) FCEV | 360/320/140 | Used when discharging hydrogen fuel tank gas. |
|
| |
09356-4W140 | PORTABLE DEVICE | Tucson(LM)/NEXO(FE) FCEV | 1100/340/330 | Used when discharging hydrogen fuel tank gas. |
|
| |
09356-4W150 | Fuel tank removal/installation support | Tucson(LM) FCEV | 1200/780/300 | Used as a support when removing/installing the hydrogen tank of a hydrogen fuel cell vehicle. |
|
| |
09356-4W160 | Stack PMC module removal/installation support | Tucson(LM) FCEV | 1320/920/350 | Used when removing/installing the hydrogen fuel cell vehicle stack PMC module. |
|
| |
09356-4W161 | DISASSEMBLY SUPPORTER OF STACK | NEXO(FE) FCEV |
|
||
| |
09356-4W162 | Stack partialization hanger | NEXO(FE) FCEV |
|
||
| |
09356-4W170 | COOLANT HOSE CORK SET | Tucson(LM)/NEXO(FE) FCEV | 480/370/200 | It is used to prevent coolant discharge from the pipe hose of the hydrogen fuel cell vehicle motor. |
|
| |
09356-4W180 | OIL SEAL INSTALLER(Motor) | Tucson(LM) FCEV | 110/75/75 | Used when installing the oil seal of the driving motor of a hydrogen fuel cell vehicle. |
|
| |
09356-4W190 | OIL SEAL INSTALLER | Tucson(LM) FCEV | 145/70/70 | Used when installing the reducer oil chamber. |
|
| |
09356-4W200 | DIFF CARRIER HANGER | Tucson(LM) FCEV | 85/60/30 | It is used when transporting the driving motor of a hydrogen fuel cell vehicle. |
|
| |
09356-4W220 | STACK HANGER | Tucson(LM) FCEV | 400/350/130 | Used when moving the hydrogen fuel cell vehicle stack. |
|
| |
09356-4W270 | HIGH PRESSURE FUEL FITTING O-RING MOUNTING TOOL | Tucson(LM)/NEXO(FE) FCEV | 290/225/120 | Used when installing a high pressure sensor O-ring. |
|
| |
09356-5M120 | HYDROGEN LINE RESIDUAL PRESSURE RELEASING ADAPTER | NEXO(FE) FCEV | 88/19/19 | Used when installing the oil seal of the driving motor of a hydrogen fuel cell vehicle. |
|
| |
09356-5M150 | HYDROGEN TANK SUPPORTER & INSTALLATION JIG | NEXO(FE) FCEV | 930/600/400 | Used when installing or dismounting the fuel tank. |
|
| |
09356-5M200 | Drive motor hanger | NEXO(FE) FCEV | 42/62/22 | Used when installing the oil seal of the driving motor of a hydrogen fuel cell vehicle. |
|
| |
09356-5M240 | STACK COOLANT INLET/OUTLET CORK | NEXO(FE) FCEV | 108/109/35 | Used to seal stack coolant. |
|
| |
09356-5M250 | STACK RESIDUAL HYDROGEN GAS REMOVAL ADAPTER | NEXO(FE) FCEV | 95/80/60 | Used to remove residual hydrogen inside the stack. |
|
| |
09356-5M270 | FUEL TUBE AND SENSOR SECTION O-RING INSTALLER | NEXO(FE) FCEV | 85/17/17 | Used when installing a high pressure sensor O-ring. |
|
| |
09356-5M280 | STACK HANGER | NEXO(FE) FCEV | 66/70/18 | Used when removing/installing the stack. |
|
| |
09356-5M290 | STACK MODULE HANGER adapter | NEXO(FE) FCEV | 590/120/80 | Used when removing/installing stack & drive motor assembly. |
|
| |
09356-5M291 | STACK MODULE HANGER | NEXO(FE) FCEV |
|
||
| |
09356-5M292 | STACK MODULE ADAPTER | NEXO(FE) FCEV |
|
||
| |
09356-5M293 | STACK HANGER | NEXO(FE) FCEV | 280/250/65 | Used when installing or dismounting the stack |
|
| |
09356-5M300 | RESIDUAL HYDROGEN FORCED DISCHARGE ADAPTER IN HYDROGEN TAN | NEXO(FE) FCEV | 105/50/20 | Used to forcibly discharge residual hydrogen in a hydrogen tank. |
|
 |
09356-LK100 | Wheel & tire attachment/detachment guide | LK FCEV | 260/105/26 | Used as a guide when removing/installing the rear wheel |
|
| |
09356-LK130 | FUEL PRESSURE GAUGE & HOSE | LK FCEV | 360/320/140/ |
|
|
| |
09356-LK250 | STACK RESIDUAL HYDROGEN GAS REMOVAL ADAPTER | LK FCEV | 70/70/60 | Used to remove residual hydrogen inside the stack. |
|
| |
09356-LM200 (Improvement of commonization) |
STACK MODULE HANGER | universe(PY)/LM/Elec-city(LK) FCEV | 1375/620/220 | Used by connecting to the stack when removing/installing the PMC (stack) |
|
| |
09356-M5100 | SUCTION GUN OF INLET FITTING HOLE | NEXO(FE) FCEV |
|
||
| |
09356-M5101 | Inlet fitting hole suction hose adapter | NEXO(FE) FCEV |
|
||
| |
09356-M5102 | Inlet fitting hole suction nozzle | NEXO(FE) FCEV |
|
||
|
09375-0E100 | Battery transfer hanger | IONIQ(AE) EV | 1310/185/154 | Used when removing/installing a high-voltage battery. |
|
| 09375-0E102 | Side Frame | KS (Indonesia) |
|
|||
|
|
09375-GI000 | Gap-Filler Apply Tool | IONIQ5(NE) EV, GENESIS80(RG3) EV | High-voltage battery gap filler work can be performed conveniently at a constant speed. |
|
|
|
|
09375-GI100 | GAP FILLER SUPORT | IONIQ5(NE) EV, GENESIS80(RG3) EV | 1255/680/645 | High-voltage battery gap filler work can be performed conveniently at a constant speed. |
|
| 09375-GI200 | GAP FILLER GUN | IONIQ5(NE) EV, GENESIS80(RG3) EV | 295/155/585 | High-voltage battery gap filler work can be performed conveniently at a constant speed. | ||
| |
09375-GI300 | GAP FILLER RIBBON | IONIQ5(NE) EV, GENESIS80(RG3) EV | 82/40/100 | High-voltage battery gap filler work can be performed conveniently at a constant speed. |
|
| 09430-7M800 | axle fixing tool | XCIENT(QZ) T160F | 130/130/148 | Used when installing the rear (T160F) oil seal during overhaul work. |
|
|
| 09430-7M900 | Rear oil seal installed | XCIENT(QZ) T160J | 130/130/154 | Used when installing the rear (T160F) oil seal during overhaul work. |
|
|
| 09430-A5110 | ACTUATOR SPACER & BOLT |
KAPPA 1.0 Engine | 50/16/16 | Used when removing/installing the DCT actuator. |
|
|
| 09430-C1270 | BEARING INSTALLER | SONATA(LF) | 55/55/45 | Mount the bearing on the tool and insert it into the shaft. |
|
|
| 09451-D2100 | Torque converter fixing bolt removal tool | EQ900(HI) | 85/27/25 | Used when installing or dismounting the torque converter mounting bolt. |
|
|
|
|
09495-GI100 | BAND CLAMP PLIERS | IONIQ5(NE) EV 외 | Used when installing drive shaft boot band |
|
|
| 09517-7M170 | hub mounting guide | XCIENT(QZ) | 105/105/55 | It is used when removing/installing the hub of the disk type. |
|
|
| 09517-QZ500 | Rear wheel hub nut removal/installation tool | XCIENT Specially equipped vehicle | 112/112/80 | Remove/install the rear hub nut using the developed tool. |
|
|
| 09517-QZ800 | P/Shaft U-Joint bearing removal tool | XCIENT(QZ) | Used to remove propeller shaft joint bearing |
|
||
| 09521-59220 | axle fixing tool | SOLATI(EU) | 705/380/40 | Used to remove/install the rear axle. |
|
|
| 09527-2W110 | WHEEL BEARING SENSOR INSTALLER | SANTA FE(DM),MAXCRUZ(NC), SORENTO(XM),CARNIVAL(YP),KX7(QM),CK(FRT),GENESIS G70(IK)-FRT | 89/89/55 | Used when installing a tone wheel sensor |
|
|
| 09530-3C300 | Differential assembly fixed die adapter | GEMESIS G80(DH) | 410/260/77 |
|
||
| 09530-7M600 | Pinion cage mounting | XCIENT(QZ) | 160/150/80 | Used when installing pinion cage during overhaul work. |
|
|
| 09530-7M710 | Install pinion oil seal | XCIENT(QZ) | 162/162/108 | Used when installing pinion oil during overhaul work. |
|
|
| 09546-S1100 | SHOCK ABSORBER LOCK NUT REMOVAL TOOL | SANTA FE(TM) | 365/160/90 | Used when installing or removing the rear shock lock nut. |
|
|
| 09563-B4000 | Worm Shaft tool Set | Bi3, HCI, IB, QXI | 460/258/154 |
|
||
| 09563-B4001 | Plug bolt lock nut tool 65-01 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4002 | Plug bolt tool 65-02 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4003 | Output shaft lock nut tool-1 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4004 | Output shaft lock nut tool-2 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4005 | Plug bolt lock nut tool 35-03 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4006 | Plug bolt tool 35-04 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4007 | Upper shaft-1 | Bi3, HCI, IB, QXI |
|
|||
| 09563-B4008 | Upper shaft-2 | Bi3, HCI, IB, QXI |
|
|||
| 09571-8D200 | L-Engine Power Steering Pump Gear Fixing Tool | L-ENGIN | 110/85/20 | Used to secure the steering pump gear and remove the lock nut. |
|
|
| |
09876-KL000 | CE EV DSM calibration Target | IONIQ6(CE) EV | 340/402/60 |
|
|
| 09890-6D400 | CORRECTION JIG FOR FRONT VIEW CAMERA | PAVISE MEGA TRUCK (QV) | 125/88/34 | It helps when installing a calibration panel for LDWS calibration. |
|
|
| 09890-6D500 | LINE LASER / COMPENSATOR DISTANCE WIRE | PAVISE MEGA TRUCK (QV) | 120/80/30 | Helps when installing a correction reflector for SCC correction. |
|
|
| 0K214-P2600 | BALANCE SHAFT HOLDER | NEW R 2.2 ENGIN | 220/220/35 | Remove the BSA cap and install the SST into the hole on the side of the engine block to prevent shaft rotation. |
|
|
| 0K240-P2100 | TIMING BELT TENSIONER ROTATION | SORENTO(MQ4)_NEW R2.2 | 90/65/37 | Used when reassembling the timing tensioner. |
|
|
| 0K240-P2300 | HIGH PRESSURE FUEL PUMP PULLEY FIXING PIN | SORENTO(MQ4)_NEW R2.2 | 50/10//10 | Used to fix the high pressure fuel pump. |
|
|
|
0K253-G5100 | PRESSURE CAP PRESSURE CHECK ADAPTER | NIRO(DE) HEV, IONIQ(AE) HEV |
72/43/43 | Used for cooling water circulation system leak inspection and pressure cap pressure testing. |
|
|
|
0K253-J2100 | PRESURE CAP PRESURE CHECKER EV Coolant(Left screw - black) |
SOUL(SK3) EV, NIRO(DE) EV, BONGO(PU) EV | 72/43/43 | Used for cooling water circulation system leak inspection and pressure cap pressure testing. |
|
|
|
0K253-J2300 | COOLANT REFILLER & DRAIN TOOL | EV,HEV, FCEV all vehicles | 574/307/154 | Used to discharge and vacuum inject coolant |
|
|
0K253-J2310 | COOLANT REFILLER & SUCTION TOOL | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2320 | CAP ADAPTOR A | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2330 | CAP ADAPTOR B | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2340 | CAP ADAPTOR C | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2350 | CAP ADAPTOR D | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2360 | CAP ADAPTOR E | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2370 | HOSE SET | EV,HEV, FCEV all vehicles |
|
||
|
0K253-J2380 | COOLANT DRAIN ADAPTOR & HOSE | EV,HEV, FCEV all vehicles |
|
||
|
0K253-P4100 | PRESURE CAP PRESURE CHECKER Hybrid coolant (left screw) |
SORENTO(MQ4)HEV | 72/43/43 | Used for cooling water circulation system leak inspection and pressure cap pressure testing. |
|
| |
0K253-P4200 | PRESURE CAP PRESURE CHECKER Engine coolant (right screw) |
SORENTO(MQ4)HEV Engine coolant | 110/95/55 | Used for cooling water circulation system leak inspection and pressure cap pressure testing. |
|
 |
0K375-4U000 | Insulated tools | EV,HEV, FCEV all vehicles | 460/340/125 | When maintaining EV/hybrid vehicles, newly developed SST (shared tools) are used. |
|
| |
0K375-E4300 | HV BATTERY PACK ASSEMBLY LIFTING FIXTURE | SOUL(PS) EV | 755/400/135 | Used when removing/installing the battery assembly. |
|
| 0K431-Q5100 | DIFFERENTIAL OUTER RACER INSATALLER | DCT GEN2 | 85/85/20 | Used when installing DCT differential bearing outer racer. |
|
|
| 0K431-Q5200 | INPUT SHAFT OLI SEAL INSATALLER | DCT GEN2 | 50/50/20 | Used when installing DCT input oil seal. |
|
|
| 0K431-Q5300 | OUTPUT SHAFT TWO-AXIS BEARING REMOVAL | DCT GEN2 | 140/200/12 | Used to remove the bearing on the DCT output axis 2 housing side. |
|
|
| 0K431-Q5400 | GEAR ASSEMBLY INSATALLER & REMOVAL | DCT GEN2 | 280/290/270 | Used when installing or dismounting the DCT gear assembly. |
|
|
| 0K495-C5000 | DRIVESHAFT BOOT BAND INSTALLER | Omega type all models | 37.5/10/3.5 | Used when installing or dismounting the DCT gear assembly. |
|
|
| 0K530-P2400 | BACKLASH MEASUREMENT SUPPORTER. | SORENTO(MQ4) | 110/95/55 | Used to measure rear differential gear backlash. |
|
|
| 0K530-P2500 | REAR DIFFERENTIAL ASSEMBLY WORKING STAND | SORENTO(MQ4) | 220/220/35 | Used in case of differential carrier failure. |
|
|
|
|
0K876-DO100 | DE EV DSM calibration Target | NIRO(DE) EV | 420/502/58 |
|
|
| 0K964-J5100 | RADAR CALIBRATION REFLECTOR | SORENTO(QM), STIGER(CK) |
210/210/130 | Used for forward radar (FCA, SCC) correction. |
|
|
|
|
A08 | protective glasses | Tucson(LM)/NEXO(FE) FCEV |
|